Stepper motor basics

A standard bipolar stepper-motor usually will have 1.8 degree steps. That will be 200 steps per revolution. It has two motor windings (phase A and B) that must be controlled. The motor is rated at some maximum current per phase. That means, it will be the maximum current in each winding.

Project photograph or diagram

If we look at the data sheet for a specific motor we find: Maximum current pr phase: 1.4 A Resistance per phase: 4.2  Ohms Inductance per phase: 15 mH Thus, if you put 5.88V (~6V) across a phase, it will reach its maximum current. V = R * I = 4.2Ω * 1.4A = 5.88V Normally we can control this current with a resistor in serial with the phase or we can use PWM (Pulse with Modulation). If we have 12V for our motor, it will have to be at about 50% duty cycle to meet the maximum rating. A standard full step cycle consist of 4 steps. Thesesteps must the be repeated over and over again, to make the motor turn. If we reverse the cycle the motor will turn in reverse.

Project photograph or diagram

As we see from the table above, we will have to inverse the polarity of the phase voltage every other step. To do this we can use a standard H-bridge. With two H-bridges we can control the current in both phases.

PWM, constant current and chopper drivers

The first problem to overcome is the inductance in each windings. In the data sheet it says 15 mH for this particular stepper motor. This inductance will cause the current to change slowly, and it will prevent fast stepping rates. If we look at a simple simulation in LTSpice, only considering the inductance and not any back EMF or other things in the motor, it will look like this:

Project photograph or diagram

At 6V, if the frequency in each phase is 25Hz, the voltage and current flow will look like this:

Project photograph or diagram

Project photograph or diagram

At 166 Hz and 6V the current will look like this:

Project photograph or diagram

As we can se from the plots above, we will not be able to feed the proper amount of current for the motor at higher stepping-rates. Eventually the stepper motor will stall and just stop at some point if we further increase the step rate. 166Hz is not that fast. The motor will do 4 steps for each period. Each period is 6ms. Time per revolution is then: t=200/4*6ms = 0.3s rpm = 60/0.3 = 200 (And then 2/3 of the torqu is gone. This is too slow for most applications) We need some higher voltage to force more current in the motor. But we must ensure the current will not exceed the maximum rating for the motor. The easiest way of doing this is to use a chopper driver for the motor. This will feed the motor the higher voltage until the current limit is reached. The stepper driver will the use PWM to hold the current constant. It will look something like this at 60V and 166Hz:

Project photograph or diagram

We can than increase the step rate without burning the motor. The power dissipation will be the same because P=I*I*R = 1.4A*1.4A*4.2Ohm = 8.2W for each phase. For the motor it will be Pa+Pb= 16.4W

Half step and micro-step

If we look at the phase currents in another way (phase diagram), by plotting the current of phase A vs the current of phase B, we will have this diagram:

Project photograph or diagram

In the diagram above the first step will be the point at the upper right, step two will be at bottom right, step tree at bottom left and step four will be at the top left. If we follow the steps from 1-4 the plots will go clockwise in the diagram. In half step the current table will look like this:

Project photograph or diagram

And the phase diagram will look like this.

Project photograph or diagram

At 1/4 micro-stepping we will use this table:

Project photograph or diagram

Project photograph or diagram

As we can see from the diagram above, we will have maximum torque possible for each micro step. But step number 1 have more torque than step 0, step 2 have more that step 1. The highest torque is the steps in the corners in the phase diagram. The torque is the length from center to the step-plot. This is because, if we energize both windings, the motor will have more torque than if we only energize one winding. This will cause the motor to rotate a bit choppy, and there will be some vibrations. To overcome this problem, it's better to use wave-stepping.

Wave micro-stepping

At the next table we see that only one phase is energized at a time. For full steps this method only decreases the torque, and does not really give any benefits.

Project photograph or diagram

Project photograph or diagram

With half step wave, we will see that every step is having the same torque, and the motor will run smoother:

Project photograph or diagram

Project photograph or diagram

At 1/4 micro-stepping we will just increase the resolution of the current table. The driver electronics will have to control the current according to the table for each micro-step.

Project photograph or diagram

Project photograph or diagram

At 1/8 micro-stepping we will se that the current in each phase is actually a SIN and a COS. Each phase is 90 degree from each other.

Project photograph or diagram

Project photograph or diagram

Project photograph or diagram

The formulas for current in an 1/8 micro-stepping configuration are: Ia = SIN(Stepnumber*360/32)Imax Ib = COS(Stepnumber*360/32)Imax For 1/16 microstepping it will be: Ia = SIN(Stepnumber*360/64)Imax Ib = COS(Stepnumber*360/64)Imax For 1/32 microstepping it will be: Ia = SIN(Stepnumber*360/128)Imax Ib = COS(Stepnumber*360/128)Imax Files: http://www.lamja.com/blogfiles/SimpleChopperStepperMotorSimulation.asc